<div dir="ltr">Hello List.<div><br></div><div>I recently installed and configured OmniOS on a HP Microserver N40L NAS box.</div><div><br></div><div>In time to time my box hangs/freezes for some seconds, when I try to SSH into the box or execute some SMART-INFO functions.</div>
<div>And then it gives me access.</div><div><br></div><div>In my /var/adm/messages i have these messages :</div><div><br></div><div>May  8 20:10:41 blackbox scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@14,1/ide@0 (ata0):</div>
<div>May  8 20:10:41 blackbox        timeout: abort request, target=1 lun=0</div><div>May  8 20:10:41 blackbox scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@14,1/ide@0 (ata0):</div><div>May  8 20:10:41 blackbox        timeout: abort device, target=1 lun=0</div>
<div>May  8 20:10:41 blackbox scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@14,1/ide@0 (ata0):</div><div>May  8 20:10:41 blackbox        timeout: reset target, target=1 lun=0</div><div>May  8 20:10:41 blackbox scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@14,1/ide@0 (ata0):</div>
<div>May  8 20:10:41 blackbox        timeout: reset bus, target=1 lun=0</div><div>May  8 20:10:42 blackbox gda: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@14,1/ide@0/cmdk@1,0 (Disk0):</div><div>May  8 20:10:42 blackbox        Error for command 'read sector' Error Level: Informational</div>
<div>May  8 20:10:42 blackbox gda: [ID 107833 kern.notice]   Sense Key: aborted command</div><div>May  8 20:10:42 blackbox gda: [ID 107833 kern.notice]   Vendor 'Gen-ATA ' error code: 0x3</div><div><br></div><div>
<br></div><div>My current configuration is the System(OmniOS) is installed onto a SATA disk located at port 5 on the Microserver.</div><div>(yes i have the BIOS hacked which allows for SATA 3G/AHCI functions on the port other ports)</div>
<div>Then I have 4x SATA disks configured in RAIDZ</div><div><br></div><div>I double checked my BIOS configuration, and it seems that I have misconfigured the OS disk into a IDE mode, but not AHCI.</div><div>So when I change the mode to AHCI, I get the GRUB loader and the OmniOS logo after that, but suddenly the machines restarts again</div>
<div>and never boots into the system all the way.</div><div><br></div><div>So my question is, is there any way for my to reconfigure my running-system to use AHCI instead of IDE,ATA mode ?</div><div><br></div><div>Is it enough to boot up a usb live system and issue a "zpool import -f rpool", and then finally "zpool export rpool" with a running BIOS-config as AHCI</div>
<div>and then restart the computer and let it boot normally ? I read somewhere that the import/export functions would update the device path, but I have no experience on this issue.</div><div><br></div><div>Any help would be much appreciated.</div>
<div><br></div><div>Thanks allot people.</div><div><br></div><div>Best regards,</div><div><br></div><div>Svavar O</div><div>Reykjavik - Iceland</div><div><br></div><div> </div><div>
</div></div>